P. O. Box 380 Orange City, ia 51041



Download 196.91 Kb.
Page1/3
Date06.02.2017
Size196.91 Kb.
  1   2   3


http://www.arcat.com/clients/gfx/diamvog.gif

SECTION 09 90 00



PAINTS AND COATINGS
Display hidden notes to specifier. (Don't know how? Click Here)
Copyright 2016 - 2016 ARCAT, Inc. - All rights reserved
** NOTE TO SPECIFIER ** Diamond Vogel, interior and exterior paints and coatings.
This section is based on the products of Diamond Vogel, which is located at:
1110 Albany Pl. S.E.
P.O. Box 380
Orange City, IA 51041
Toll Free Tel: 800-72-VOGEL
Phone: 712-737-8880
Fax:712-737-4998
Email:
Web:www.diamondvogel.com
[Click Here] for additional information
Diamond Vogel makes a full range of architectural and heavy-duty protective coatings so we have the right product for your project. Product lines include Diamond Vogel Architectural, Pinnacle Protective Coatings, and Old Masters.


  1. GENERAL

    1. SECTION INCLUDES

** NOTE TO SPECIFIER ** Delete items below not required for project.

      1. Field painting including surface preparation including the following:

        1. Exterior coating systems.

        2. Interior coating systems.

        3. Interior low-VOC coating systems that meet VOC requirements of LEED-09 - NC.

        4. Exterior high-performance coating systems.

        5. Interior high-performance coating systems.

    1. RELATED SECTIONS

** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.

      1. Section 03 30 00 - Cast-in-Place Concrete.

      2. Section 05 12 16 - Fabricated Fireproofed Steel Columns.

      3. Section 05 21 23 - Steel Joist Girder Framing.

      4. Section 05 50 00 - Metal Fabrications.

      5. Section 06 20 00 - Finish Carpentry.

      6. Section 08 11 13.16 - Custom Hollow Metal Doors and Frames.

      7. Section 09 21 16.23 - Gypsum Board Shaft Wall Assemblies.

      8. Section 23 05 00 - Common Work Results for HVAC.

      9. Section 26 05 00 - Common Work Results for Electrical.

    1. REFERENCES

** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.

      1. Master Painters Institute (MPI): Architectural Painting Manual.

      2. Society for Protective Coatings: SSPC SP6 - Commercial Blast Cleaning Procedure.

      3. Society for Protective Coatings: SSPC SP10 - Near White Blast Cleaning Procedure.

    1. DEFINITIONS

      1. General: Standard coating terms defined in Master Painters Institute (MPI) Architectural Painting Manual.

        1. Flat refers to a lusterless or matte finish with a gloss range between 0 and 5 when measured at a 60 degree meter.

        2. Eggshell refers to a low-sheen finish with a gloss range between 10 and 25 when measured at a 60 degree meter.

        3. Satin refers to a low-sheen finish with a gloss range between 20 and 35 when measured at a 60 degree meter

        4. Semigloss refers to a medium-sheen finish with a gloss range between 35 and 70 when measured at a 60 degree meter.

        5. Gloss refers to a high-sheen finish with a gloss range more than 70 when measured at a 60 degree meter.

    2. SUBMITTALS

      1. Submit under provisions of Section 01 30 00 - Administrative Requirements.

      2. Product Data: For each paint system indicated, including:

        1. Material List: An inclusive list of required coating materials. Indicate each material and cross reference specific coating, finish system, and application. Identify each material by manufacturer's catalog number and general classification.

        2. Preparation instructions and recommendations.

        3. Manufacturer's Information: Manufacturer's technical information, including label analysis and instructions for handling, storing, and applying each coating material.

** NOTE TO SPECIFIER ** Delete selection samples if colors have already been selected.

      1. Selection Samples: For each finish product specified, two complete sets of color chips representing manufacturer's full range of available colors and patterns.

      2. Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) square, representing actual product, color, and patterns.

    1. QUALITY ASSURANCE

      1. Installer Qualifications: A firm or individual experienced in applying paints and coatings similar in material, design, and extent to those indicated for this Project, whose work has resulted in applications with a record of successful in-service performance.

      2. Obtain block fillers and primers for each coating system from the same manufacturer as the finish coats.

      3. Paint exposed surfaces. If an item or a surface is not specifically mentioned, paint the item or surface the same as similar adjacent materials or surfaces. If a color of finish is not indicated, Architect will select from standard colors and finishes available.

      4. Do not paint prefinished items, concealed surfaces, finished metal surfaces, operating parts, and labels.

** NOTE TO SPECIFIER ** Include a mock-up if the project size and/or quality warrant taking such a precaution. The following is one example of how a mock-up on a large project might be specified. When deciding on the extent of the mock-up, consider all the major different types of work on the project.

      1. Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship.

        1. Finish areas designated by Architect.

        2. Do not proceed with remaining work until workmanship, color, and sheen are approved by Architect.

        3. Refinish mock-up area as required to produce acceptable work.

    1. DELIVERY, STORAGE, AND HANDLING

      1. Deliver materials to Project site in manufacturer's original, unopened packages and containers bearing manufacturer's name and label:

      2. Store materials not in use in tightly covered containers in a well-ventilated area at a minimum ambient temperature of 45 deg F (7 deg C). Maintain storage containers in a clean condition, free of foreign materials and residue.

    2. PROJECT CONDITIONS

      1. Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits.

      2. Apply waterborne paints only when temperatures of surfaces to be painted and surrounding air are between 50 and 90 deg F (10 and 32 deg C) unless otherwise stated in the manufacturer's instructions.

      3. Apply solvent-thinned paints only when temperatures of surfaces to be painted and surrounding air are between 45 and 95 deg F (7 and 35 deg C).

      4. Do not apply paint in snow, rain, fog, or mist; or when relative humidity exceeds 85 percent; or at temperatures less than 5 deg F (3 deg C) above the dew point; or to damp or wet surfaces.

        1. Painting may continue during inclement weather if surfaces and areas to be painted are enclosed and heated within temperature limits specified by manufacturer during application and drying periods.

** NOTE TO SPECIFIER ** Extra materials may not be allowed for publicly funded projects. Do not include for High Performance Coatings (HPC). Delete if not required.

    1. EXTRA MATERIALS

      1. Furnish extra paint materials from the same production run as the materials applied and in the quantities described below. Package with protective covering for storage and identify with labels describing contents. Deliver extra materials to Owner's storage area.

      2. Quantity: Furnish Owner with an additional three percent, but not less than 1 gal (3.8 l) or 1 case, as appropriate, of each material and color applied.

  1. PRODUCTS

    1. MANUFACTURERS

      1. Acceptable Manufacturer: Diamond Vogel Paints, which is located at: 1110 Albany Pl. S. E. P. O. Box 380; Orange City, IA 51041; Toll Free Tel: 800-72-VOGEL; Tel: 712-737-8880; Fax: 712-737-4998; Email: request info (marketing@diamondvogel.com); Web: www.diamondvogel.com

** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.

      1. Substitutions: Not permitted.

      2. Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.

    1. PAINT MATERlALS - GENERAL

      1. Material Compatibility: Provide block fillers, primers, and finish-coat materials that are compatible with one another and with the substrates indicated under conditions of service and application, as demonstrated by manufacturer based on testing and field experience.

** NOTE TO SPECIFIER ** Revise VOC rating to suit local regulations or Owner's requirements. Delete if not required.

      1. VOC Classification: Provide high-performance coating materials, including primers, undercoats, and finish-coat materials, that meet the applicable local, state or federal VOC requirements.

      2. Color: Refer to Finish Schedule and Paint Legend on the Drawings for paint colors.

      3. Application Rate: Coating thickness for primer, intermediate, barrier and finish coats shall be measured as Dry Film Thickness (DFT) and comply with manufacturer's published recommendations.

** NOTE TO SPECIFIER ** Delete if not required.

    1. EXTERIOR COATING SYSTEMS

** NOTE TO SPECIFIER ** Delete if not required.

      1. Exterior Concrete Block (Porous Lightweight and Split Face):

        1. Acrylic Finish: Two finish coats over an acrylic block filler.

          1. Block Filler: Diamond Vogel DiaPro Acrylic Block Filler.

** NOTE TO SPECIFIER ** Delete sheens not required.

          1. Finish Coat, Flat: Diamond Vogel Weather Plate Exterior Flat Acrylic Latex.

          2. Finish Coat, Satin: Diamond Vogel Weather Plate Exterior Satin Acrylic Latex.

** NOTE TO SPECIFIER ** Delete if not required.

      1. Exterior Concrete Block (Regular Weight, Smooth Face):

        1. Acrylic Finish: Two finish coats over an exterior primer.

          1. Primer: Diamond Vogel Weather Plate Exterior Acrylic Latex Primer.

** NOTE TO SPECIFIER ** Delete sheens not required.

          1. Finish Coat, Flat: Diamond Vogel Weather Plate Exterior Flat Acrylic Latex.

          2. Finish Coat, Satin: Diamond Vogel Weather Plate Exterior Satin Acrylic Latex.

** NOTE TO SPECIFIER ** Delete if not required.

      1. Exterior Poured Concrete (Tilt-Up and Pre-Stress Panels):

        1. Acrylic Finish: Two finish coats over an exterior primer.

          1. Primer: Diamond Vogel Weather Plate Exterior Acrylic Latex Primer.

** NOTE TO SPECIFIER ** Delete sheens not required.

          1. Finish Coat, Flat: Diamond Vogel Weather Plate Exterior Flat Acrylic Latex.

          2. Finish Coat, Satin: Diamond Vogel Weather Plate Exterior Satin Acrylic Latex.

** NOTE TO SPECIFIER ** Delete if not required.

      1. Fiber Cement Siding, Bare:

        1. Acrylic Finish: Two finish coats over an exterior primer.

          1. Primer: Diamond Vogel Weather Plate Exterior Acrylic Latex Primer.

** NOTE TO SPECIFIER ** Delete sheens not required.

          1. Finish Coat, Flat: Diamond Vogel Weather Plate Exterior Flat Acrylic Latex.

          2. Finish Coat, Satin: Diamond Vogel Weather Plate Exterior Satin Acrylic Latex.

** NOTE TO SPECIFIER ** Delete if not required.

      1. Fiber Cement Siding, Pre-primed:

        1. Acrylic Finish: Two finish coats.

** NOTE TO SPECIFIER ** Delete sheens not required.

          1. Finish Coat, Flat: Diamond Vogel Weather Plate Exterior Flat Acrylic Latex.

          2. Finish Coat, Satin: Diamond Vogel Weather Plate Exterior Satin Acrylic Latex.

** NOTE TO SPECIFIER ** Delete if not required.

      1. Exterior Ferrous Metal, Bare:

** NOTE TO SPECIFIER ** Select one or more of the systems below. Delete systems not required.

        1. Acrylic Finish: Two finish coats over a water-based, rust-inhibitive primer.

          1. Primer: Pinnacle Protective Coatings Vers-Acryl 200 Acrylic Maintenance Primer/Finish.

** NOTE TO SPECIFIER ** Delete sheens not required.

          1. Finish Coat, Flat: Diamond Vogel Weather Plate Exterior Flat Acrylic Latex.

          2. Finish Coat, Satin: Diamond Vogel Weather Plate Exterior Satin Acrylic Latex.

        1. Alkyd Finish: Two finish coats over an alkyd, metal primer.

          1. Primer: Pinnacle Protective Coatings CoteAll Multi-Purpose Alkyd Primer.

          2. Finish Coat: Pinnacle Protective Coatings CoteAll Multi-Purpose Alkyd Enamel.

** NOTE TO SPECIFIER ** Delete if not required.

      1. Exterior Ferrous Metal, Pre-primed:

** NOTE TO SPECIFIER ** Select one or more of the systems below. Delete systems not required.

        1. Acrylic Finish: Two finish coats over a water-based, rust-inhibitive primer.

          1. Primer: Pinnacle Protective Coatings Vers-Acryl 200 Acrylic Maintenance Primer/Finish.

** NOTE TO SPECIFIER ** Delete sheens not required.

          1. Finish Coat, Flat: Diamond Vogel Weather Plate Exterior Flat Acrylic Latex.

          2. Finish Coat, Satin: Diamond Vogel Weather Plate Exterior Satin Acrylic Latex.

        1. Alkyd Finish: Two finish coats over an alkyd, metal primer.

          1. Primer: Pinnacle Protective Coatings CoteAll Multi-Purpose Alkyd Primer.

          2. Finish Coat: Pinnacle Protective Coatings CoteAll Multi-Purpose Alkyd Enamel.

** NOTE TO SPECIFIER ** Delete if not required.

      1. Galvanized or Zinc-Coated Metal:

** NOTE TO SPECIFIER ** Select one or more of the systems below. Delete systems not required.

        1. Acrylic Finish: Two finish coats over a water-based, rust-inhibitive primer.

          1. Primer: Pinnacle Protective Coatings Vers-Acryl 200 Acrylic Maintenance Primer/Finish.

** NOTE TO SPECIFIER ** Delete sheens not required.

          1. Finish Coat, Flat: Diamond Vogel Weather Plate Exterior Flat Acrylic Latex.

          2. Finish Coat, Satin: Diamond Vogel Weather Plate Exterior Satin Acrylic Latex.

        1. Alkyd Finish: Two finish coats over an alkyd, metal primer.

          1. Primer: Pinnacle Protective Coatings Iron Prime 600 Fast Dry Universal Primer.

          2. Finish Coat: Pinnacle Protective CoatingsCoteAll Multi-Purpose Alkyd Enamel.

** NOTE TO SPECIFIER ** Delete if not required.

      1. Aluminum:

** NOTE TO SPECIFIER ** Select one or more of the systems below. Delete systems not required.

        1. Acrylic Finish: Two finish coats over a water-based, rust-inhibitive primer.

          1. Primer: Pinnacle Protective Coatings Vers-Acryl 200 Acrylic Maintenance Primer/Finish.

** NOTE TO SPECIFIER ** Delete sheens not required.

          1. Finish Coat, Flat: Diamond Vogel Weather Plate Exterior Flat Acrylic Latex.

          2. Finish Coat, Satin: Diamond Vogel Weather Plate Exterior Satin Acrylic Latex.

        1. Alkyd Finish: Two finish coats over an alkyd, metal primer.

          1. Primer: Pinnacle Protective Coatings CoteAll Multi-Purpose Alkyd Primer.

          2. Finish Coat: Pinnacle Protective Coatings CoteAll Multi-Purpose Alkyd Enamel.

** NOTE TO SPECIFIER ** Delete if not required.

      1. Wood, Opaque:

        1. Acrylic Finish: Two finish coats over a primer.

          1. Primer: Diamond Vogel Sure Grip Exterior 100% Acrylic Latex Primer.

** NOTE TO SPECIFIER ** Delete sheens not required.

          1. Finish Coat, Flat: Diamond Vogel Weather Plate Exterior Flat Acrylic Latex.

          2. Finish Coat, Satin: Diamond Vogel Weather Plate Exterior Satin Acrylic Latex.

** NOTE TO SPECIFIER ** Delete if not required.

      1. Wood, Stain:

        1. Exterior Oil Stain System: Two finish coats.

          1. Finish Coat: Diamond Vogel Grain Stain Exterior Oil Stain.

** NOTE TO SPECIFIER ** Delete if not required.

      1. Wood, Clear:

** NOTE TO SPECIFIER ** Select one or more of the systems below. Delete systems not required.

        1. Exterior Spar-Marine Clear Finish: Two finish coats.

** NOTE TO SPECIFIER ** Delete sheens not required.

          1. Finish Coat, Gloss: Old Masters Exterior Spar-Marine Clear Gloss Finish.

          2. Finish Coat, Semi-Gloss: Old Masters Exterior Spar-Marine Clear Semi-Gloss Finish.

        1. Exterior Spar-Marine Clear Finish: Three finish coats.

** NOTE TO SPECIFIER ** Delete sheens not required.

          1. Finish Coat, Gloss: Old Masters Exterior Spar-Marine Clear Gloss Finish.

          2. Finish Coat, Semi-Gloss: Old Masters Exterior Spar-Marine Clear Semi-Gloss Finish.

** NOTE TO SPECIFIER ** Delete if not required.

    1. INTERIOR COATING SYSTEMS

** NOTE TO SPECIFIER ** Delete if not required.

      1. Gypsum Board, Walls:

        1. Latex Finish: Two finish coats over a primer.

          1. Primer: Diamond Vogel PosiPrime Interior Primer/Sealer.

** NOTE TO SPECIFIER ** Delete sheens and finishes not required.

          1. Finish Coat, Flat: Diamond Vogel Assure Interior Flat Latex Enamel.

          2. Finish Coat, Flat: Diamond Vogel Zero Plus Interior Flat Latex Enamel.

          3. Finish Coat, Eggshell: Diamond Vogel Assure Interior Eggshell Latex Enamel.

          4. Finish Coat, Eggshell: Diamond Vogel Zero Plus Interior Eggshell Latex Enamel.

          5. Finish Coat, Semi-Gloss: Diamond Vogel Assure Interior Semi-Gloss Latex Enamel.

          6. Finish Coat, Semi-Gloss: Diamond Vogel Zero Plus Interior Semi-Gloss Latex Enamel.

      1. Plaster:

        1. Latex Finish: Two finish coats over a primer.

          1. Primer: Diamond Vogel OmniPrep Universal Interior Primer.

** NOTE TO SPECIFIER ** Delete sheens and finishes not required.

          1. Finish Coat, Flat: Diamond Vogel Assure Interior Flat Latex Enamel.

          2. Finish Coat, Flat: Diamond Vogel Zero Plus Interior Flat Latex Enamel.

          3. Finish Coat, Eggshell: Diamond Vogel Assure Interior Eggshell Latex Enamel.

          4. Finish Coat, Eggshell: Diamond Vogel Zero Plus Interior Eggshell Latex Enamel.

          5. Finish Coat, Semi-Gloss: Diamond Vogel Assure Interior Semi-Gloss Latex Enamel.

          6. Finish Coat, Semi-Gloss: Diamond Vogel Zero Plus Interior Semi-Gloss Latex Enamel.

      1. Masonry/Concrete Block, Non-Wet Areas:

        1. Latex Finish: Two finish coats over a block filler.

          1. Primer: Diamond Vogel UniFill Acrylic Block Filler.

** NOTE TO SPECIFIER ** Delete sheens and finishes not required.

          1. Finish Coat, Flat: Diamond Vogel Assure Interior Flat Latex Enamel.

          2. Finish Coat, Flat: Diamond Vogel Zero Plus Interior Flat Latex Enamel.

          3. Finish Coat, Eggshell: Diamond Vogel Assure Interior Eggshell Latex Enamel.

          4. Finish Coat, Eggshell: Diamond Vogel Zero Plus Interior Eggshell Latex Enamel.

          5. Finish Coat, Semi-Gloss: Diamond Vogel Assure Interior Semi-Gloss Latex Enamel.

          6. Finish Coat, Semi-Gloss: Diamond Vogel Zero Plus Interior Semi-Gloss Latex Enamel.

      1. Poured Concrete:

        1. Latex Finish: Two finish coats over a primer.

          1. Primer: Diamond Vogel OmniPrep Universal Interior Primer.

** NOTE TO SPECIFIER ** Delete sheens and finishes not required.

          1. Finish Coat, Flat: Diamond Vogel Assure Interior Flat Latex Enamel.

          2. Finish Coat, Flat: Diamond Vogel Zero Plus Interior Flat Latex Enamel.

          3. Finish Coat, Eggshell: Diamond Vogel Assure Interior Eggshell Latex Enamel.

          4. Finish Coat, Eggshell: Diamond Vogel Zero Plus Interior Eggshell Latex Enamel.

          5. Finish Coat, Semi-Gloss: Diamond Vogel Assure Interior Semi-Gloss Latex Enamel.

          6. Finish Coat, Semi-Gloss: Diamond Vogel Zero Plus Interior Semi-Gloss Latex Enamel.

      1. Ferrous Metal, Hollow Metal Doors, Frames and Other Steel:


Share with your friends:
  1   2   3


The database is protected by copyright ©dentisty.org 2019
send message

    Main page