Protected premises fire alarm system this section should be used for department of correctional services projects. This section covers a system which has one or more microprocessor based fire ala



Download 306.74 Kb.
Page2/3
Date conversion08.07.2018
Size306.74 Kb.
1   2   3

1.05 SUBMITTALS
A. Waiver of Submittals: The “Waiver of Certain Submittal Requirements” in Section 013300 does not apply to this Section.
OMIT PARAGRAPH BELOW IF EXISTING SYSTEM REPORT IS NOT REQUIRED.

B. Preliminary Submittal: Existing system test report.


C. Submittals Package: Submit the shop drawings, product data, and quality control submittals specified below at the same time as a package.

1. Company Field Advisor Letter: With the submittals package include a letter from the Company Field Advisor stating that he/she has reviewed the Submittals Package for accuracy and completeness, and approves all materials and installation methods included in the Submittals Package.

a. For 2-hour fire rated cable assemblies show proposed routes and installation details (include UL classification data, listing and system number).

b. Include transient surge and lightning protection grounding details for signaling line circuits, initiating device circuits, and ac power conductors entering and leaving each fire alarm control panel.

D. Shop Drawings:

1. Composite wiring and/or schematic diagrams of the complete system as proposed to be installed (standard diagrams will not be acceptable).

a. Indicate circuits which are power-limited if power-limited wiring is proposed for use.

2. Interconnection details between the Protected Premises Fire Alarm Systems and the Facility Monitoring and Control Multiplex System.



OMIT SUBPARAGRAPH BELOW IF NOT REQUIRED

3. Interconnection details between new system and existing sub-systems.

4. Construction and installation details for maximum security vandal guards.
E. Product Data:

1. Catalog sheets, specifications and installation instructions.

2. Bill of materials.

3. Detailed description of system operation. Format similar to SYSTEM DESCRIPTION.

4. Sample procedure, programming and print-out for alarm, acknowledgment, and system reset.

5. Total electrical load of the complete system in supervisory and alarm conditions.

a. Include for each system component which utilizes batteries the battery ampere-hour capacity recommended for each component by the Company producing the system, for the specified duration.

6. Statement from the Company producing the system, for each size and type of single conductor and multiconductor cable proposed for use, indicating that the electrical characteristics meet the requirements of the Company.

7. Data from the Company furnishing the products, proving that detection devices that receive their power from the initiating device circuit or a signaling line circuit of a fire alarm control unit are UL listed for use with the control unit.

a. Submit copy of the control unit “Installation Manual Wiring Diagrams” that were a part of the UL “UOJZ” approval process showing that the proposed products, circuits, and wiring diagrams are UL listed “Control Units System (UOJZ) for use with the control panel.

b. Submit data proving that the software and firmware is listed for use with the control panel.

c. Submit data proving that the initiating devices are listed for the intended application. Also for specific applications, such as:



SPECIFIC LISTINGS ARE REQUIRED FOR MANY APPLICATIONS. SEE SUBPARAGRAPHS BELOW FOR EXAMPLES.

1) Smoke door release accomplished directly from the smoke detecting device, show listing for release service.

2) Air duct smoke detecting devices, show listing indicating complete range of air velocities, temperature and humidity expected at the device when the air handling system is operated.

3) Smoke detecting devices installed in supply air duct downstream of the fan and filters, show detector listed for the air velocity present.

4) For smoke detecting devices installed in return air system, show listing for the air velocity present where the air leaves each smoke compartment, or in the duct system before the air enters the return air system common to more than one smoke compartment.

d. Submit data proving that relays and appliances connected to the fire alarm system which are used to initiate control of fire safety functions are listed for the purpose.

e. Submit data proving that the method(s) monitoring the connection between the fire alarm system and controlled electrical and mechanical systems for integrity are listed for the purpose.

8. Detailed description of procedure proposed to test individual initiating devices.

a. Include product information pertaining to the test equipment that will be used to perform the tests.

b. Include certified statement that the proposed test method meets the test requirements of NFPA 72 and UL 268 (cite reference to the applicable NFPA and UL paragraphs).

9. Name, address and telephone number of nearest fully equipped service organization.

a. Include list of service technicians who are NICET Level II or higher Fire Alarm Systems certified.



INCLUDE SUBPARAGRAPH BELOW IF “ELEVATOR SHUTDOWN PRIOR TO SPRINKLER OPERATION” SUBPARAGRAPH IS USED IN SYSTEM DESCRIPTION. REFER TO NFPA 72 3-9.4.

10. Response time index comparison between the elevator hoistway and machine room heat detecting devices and sprinkler heads proving that the heat detecting devices will respond and will cause elevator power shutdown prior to sprinkler operation.


F. Quality Control Submittals:

1. Copy of license required by New York State General Business Law Article 6-D for installing Fire Alarm Systems.

a. Also include copy of identification card issued by the Licensee for each person who will be performing the Work.

2. Company Field Advisor Data: Include:

a. Name, business address and telephone number of Company Field Advisor secured for the required services.

b. Certified statement from the Company listing the qualifications of the Company Field Advisor.

c. Copy of NICET Letter of Approval indicating Level III or higher Fire Alarm Systems certification.

d. Services and each product for which authorization is given by the Company, listed specifically for this project.

3. Outline of Onsite Training Programs Required of Company Field Advisor:

a. Provide a separate outline of the training programs to be used to train the maintenance and security personnel, including:

1) System overview.

2) System programming.

3) Operation of system equipment.

4) System maintenance.

5) Estimated length (time) of each segment.

G. Contract Closeout Submittals:

1. System acceptance test report.

2. Certificates:

a. Affidavit, signed by the Company Field Advisor and notarized, certifying that the system meets the contract requirements and is operating properly.

b. NFPA Record of Completion. (NFPA 72 Figure 1-6.2.1).

3. Operation and Maintenance Data:

a. Deliver 2 copies, covering the installed products, to the Director’s Representative. Include:

1) Operation and maintenance data for each product.

2) Complete point to point wiring diagrams of entire system as installed. Identify all conductors and show all terminations and splices. (Identification shall correspond to markers installed on each conductor.)

3) Name, address, and telephone number of nearest fully equipped service organization.

INCLUDE SUBPARAGRAPH BELOW WHEN SMOKE CONTROL IS A FUNCTION OF THIS SYSTEM (NFPA 101 7.3.1).

4) A suggested maintenance and testing program that will insure operational integrity of the smoke control functions of the system.


1.06 QUALITY ASSURANCE
A. Equipment Qualifications For Products Other Than Those Specified:

1. At the time of submission provide written notice to the Director of the intent to propose an “or equal” for products other than those specified. Make the “or equal” submission in a timely manner to allow the Director sufficient time to review the proposed product, perform inspections and witness test demonstrations.



2. If products other than those specified are proposed for use furnish the name, address, and telephone numbers of at least 5 comparable installations that can prove the proposed products have performed satisfactorily for 3 years. Certify in writing that the owners of the 5 comparable installations will allow inspection of their installation by the Director's Representative and the Company Field Advisor.

a. Make arrangements with the owners of 2 installations (selected by the Director) for inspection of the installations by the Director's Representative. Also obtain the services of the Company Field Advisor for the proposed products to be present. Notify the Director a minimum of 3 weeks prior to the availability of the installations for the inspection, and provide at least one alternative date for each inspection.

b. Only references from the actual owner or owner’s representative (Security Supervisor, Maintenance Supervisor, etc.) will be accepted. References from dealers, system installers or others, who are not the actual owners of the proposed products, are not acceptable.

1) Verify the accuracy of all references submitted prior to submission and certify in writing that the accuracy of the information has been confirmed.

3. The product manufacturer shall have test facilities available that can demonstrate that the proposed products meet the contract requirements.

a. Make arrangements with the test facility for the Director's Representative to witness test demonstrations. Also obtain the services of the Company Field Advisor for the proposed product to be present at the test facility. Notify the Director a minimum of 3 weeks prior to the availability of the test facility, and provide at least one alternative date for the testing.

4. Provide written certification from the manufacturer that the proposed products are compatible for use with all other equipment proposed for use for this system and meet all contract requirements.
B. UL Listing: The system shall be listed in the UL Fire Protection Equipment Directory under product category “Control Units System (UOJZ)”.
C. Test Facility: The Company producing the system shall have test facilities available which can demonstrate that the proposed system meets contract requirements.
D. Company Field Advisor: Company Field Advisor shall be National Institute for Certification in Engineering Technologies (NICET) certified as Level III or higher Fire Alarm Protection/Fire Alarm Systems Engineering Technician.

EDIT NUMBER OF HOURS TO SUIT.

1. Secure the services of a Company Field Advisor for a minimum of 40 working hours at the contract site for the following:

a. Render advice regarding installation and final adjustment of the system and integration with the Facilities Monitoring and Control Multiplex System.

b. Assist in initial programming of the system.

c. Render advice on the suitability of each signal initiating device for its particular application.

d. Witness final system test and then certify with an affidavit that the system is installed in accordance with the contract documents and is operating properly.



EDIT NUMBER OF SESSIONS AND HOURS TO SUIT IN NEXT TWO SUBPARAGRAPHS.

e. Train facility personnel on the operation, programming and maintenance of the system (minimum of two 3-hour sessions).

f. Explain available service programs to facility supervisory personnel for their consideration.
INCLUDE PARAGRAPH BELOW WHEN EXISTING SUB-SYSTEMS ARE INTERFACED WITH THE NEW SYSTEM. ADJUST NUMBER OF HOURS AND MODIFY TERMINOLOGY TO SUIT.

E. Company Field Advisor (Existing Sub-Systems): Secure the services of a Company Field Advisor from the Company of each existing sub-system for a minimum of 8 working hours at the contract site for the following:

1. Render advice and witness test of existing sub-systems.

2. Render advice on the interconnection of existing sub-systems with the new system.

3. Witness the final test of the combined new system and existing sub-systems.
1.07 MAINTENANCE
A. Service Availability: A fully equipped service organization capable of guaranteeing response time within 8 hours to service calls shall be available 24 hours a day, 7 days a week to service the completed Work.

1. Service organization personnel shall include service technicians who are National Institute for Certification in Engineering Technologies (NICET) certified as Level II or higher Fire Alarm Protection/Fire Alarm System Engineering Technician.


B. Spare Parts:

1. 50 percent spare of each type fuse.

2. 30 percent spare of each type lamp (except LED type).

MODIFY SUBPARAGRAPH BELOW IF PROJECTED BEAM DEFECTORS ARE USED. STATE THE ACTUAL NUMBER OF SPARES REQUIRED, IF ANY.

3. 20 percent spare of each type initiating device.

4. 20 percent spare of each type notification appliance.

5. 10 percent spare of each type protective devices (except steel web guards for smoke and heat detection devices).



INDICATE SPECIFIC NUMBER OF STEEL WEB GUARDS (TO BE INSTALLED BY DOCS MAINTENANCE PERSONNEL AS NEEDED).

6. ________ steel web guards for smoke and heat detection devices.

7. Two tools to remove and install each type and size of vandal resistant fastener.

PART 2 PRODUCTS
2.01 FIRE ALARM CONTROL PANELS
A. Internal Network for Buildings With More Than One Fire Alarm Control Panel: Edwards’ Systems Technology’s (Unit of GS Building Systems Corp) EST-2, EST-3, Notifier’s Fire Systems Noti Fire Net, or Simplex Time Recorder Co. 4120:

1. Equip the fire alarm control panels and other network devices with network interface modules able to function with the type of wiring specified for the network communication bus signaling line circuit.



SYSTEM CAPACITIES ARE INDICATED BELOW ONLY FOR REFERENCE. DO NOT EDIT PANELS FROM TEXT. COMPANY SUPPLYING THE SYSTEM MUST CHOOSE PROPER PANEL FOR EACH LOCATION BASED UPON REQUIRED FUNCTIONS AND CAPACITY.
EDWARDS: EST-2 NETWORK 960 POINTS, EACH PANEL 192 POINTS; EST-3 NETWORK 160,000 POINTS, EACH PANEL 2500 POINTS.
NOTIFIER: NOTI FIRE NET/200,000 POINTS; PANELS AFP 200/198 POINTS, AFP 300/198 POINTS, AFP 400/396 POINTS, AFP 1010/792 POINTS, AM 2020/1980 POINTS.
SIMPLEX: NETWORK 50,000 POINTS; PANELS 4120/4100/1000 POINTS, 4020/508 POINTS, 4010/254 POINTS.
B. Fire Alarm Control Panels: Edwards’ EST-2, EST-3, Notifier’s AFP-200, AFP-300, AFP-400, AFP-1010, AM2020, Simplex’s 4120, 4100, 4020, 4010:

1. Base selection of each fire alarm control panel upon its capacity and capabilities to the specific requirements of the system at the panels’ location.

2. Equip the approved fire alarm control panels to function as MFACP’s and ICU’s.

3. Permanently record the installed software and firmware version number within each fire alarm control panel.

4. 14 gage metal cabinet. Size as recommended by the Company producing the system.

a. Control switches, inaccessible behind hinged and locked door.

b. Alarm display and lamps visible when door is closed.

5. Annunciator (or display) which individually identifies addressable devices and identifies groups of non-addressable devices by zones.

6. Do not load visible alarm appliance circuit outputs to more than 70 percent of the FACP’s power limited rating.

7. Input circuits suitable for operation on 120 Vac primary (main) power supply and 24 Vdc secondary (battery) power supply.

8. Secondary (Battery) Power Supplies 24 Vdc: Sealed, lead-acid gelled electrolyte or maintenance free lead-calcium batteries:

a. Ampere-hour capacity to operate under load conditions specified in SYSTEM DESCRIPTION.

b. Battery charger with charging characteristics as recommended by battery manufacturer.

c. Meters for battery voltage and charging current.

d. Batteries and charger integrally mounted or separate cabinet mounted as recommended by the company producing the system.

9. Accessories as required for each FACP perform its required functions upon failure of network communications.

10. Transient surge and lightning protection for signaling line circuits, initiating device circuits, and ac power conductors entering and leaving each fire alarm control panel:

a. Signaling Line Circuits and Initiating Device Circuits: UL listed to Standard 497B; Edwards’ LTP, Notifier’s T11325-2M, or Simplex’s 2081-9027, 2081-9028, 2081-9034, 2081-9043.

b. C Power Conductors: Edwards’ TSP, Notifier’s ________, or Simplex’s 2081-9033, 2081-9042.
C. Remote Auxiliary Power Supplies: Edwards’ BPS, Notifier’s FCPS-24, Simplex’s 2080 Series:

1. 14 gage surface mounted metal cabinet. Size as recommended by the Company producing the system.

2. Control switches inaccessible behind hinged and locked doors.

3. Input circuit suitable for operation on 120Vac primary (main) power supply.

4. Regulated and filtered 24Vdc output.

5. 24 Vdc Secondary (Standby) Power Supply: Sealed, lead-acid gelled electrolyte or maintenance free lead-calcium batteries:

a. Ampere-hour capacity to operate under load conditions specified in SYSTEM DESCRIPTION.

b. Battery charger with charging characteristics as recommended by battery manufacturer.

c. Meters for battery voltage and charging current.

d. Batteries and charger integrally mounted or separate cabinet mounted as recommended by the Company producing the system.

6. Activated by host FACP via signaling line circuit loop thru addressable modules:

a. Addressable control monitor activates the power supply outputs.

b. Addressable monitor module senses power supply trouble conditions.

7. Supervised power supply, battery, and notification appliance circuits.


D. Remote Addressable Network Modules(RANM):

SHOW REMOTE NETWORK MODULES IN CONJUNCTION WITH NON-ADDRESSABLE DEVICES THAT ARE NOT AVAILABLE ADDRESSABLE WHEN IT IS DESIRABLE TO HAVE THEM ADDRESSABLE FOR IDENTIFICATION, MONITORING AND/OR CONTROL FUNCTIONS.

1. Individual Addressable Module (IAM): Edwards’ SIGA-CT1, SIGA-CT2, SIGA-MM1, SIGA-WTM, SIGA-UM, Notifier’s FFM-101, Simplex’s 2190-9172, 2190-9073.

2. Addressable Zone Adapter Module Control and Monitor Relays (ZAM): Edwards’ SIGA-CC1, SIGA-CC2, SIGA-UM, SIGA-CR, Notifier’s FFM-1, FZM-1, FCM-1, FRM-1, or Simplex’s 2190-9163, 2190-9164, 2190-9155, 2190-9156, 2190-9173.

3. Include 24Vdc auxiliary circuit(s) as required by RANM type to suit relay operations for control, monitoring, or supervisory functions; or interconnection of fire safety control functions.


E. Remote Annunciator/Control Centers (RA/CC’s): Edwards’ 2-3-ANN, 2-6 ANN/D, 3-ANN, Notifier’s INA/ACS, or Simplex’s Network Node Unit, with:

EDIT NEXT THREE SUBPARAGRAPHS AS REQUIRED FOR ENCLOSURE TYPE.

1. Surface mounted enclosure.

2. Flush mounted enclosure.

3. LCD that is capable of displaying all system points.

4. Master enable/disable key switch for all control switches behind hinged and locked door having windows for visibility of system functions.

IF IT IS DESIRED TO HAVE VISUAL INDICATION FOR MORE THAN THE ONE SPECIFIC LIFE SAFETY CONTROL-BY-EVENT FUNCTION SPECIFIED BELOW, ADD IT BELOW. COORDINATE SUBPARAGRAPH WITH SYSTEM DESCRIPTION.

5. Annunciator modules for visible indication of specific life safety control-by-event functions:

a. Status of alarm notification appliances.

IF IT IS DESIRED TO HAVE MORE THAN THE ONE SPECIFIC LIFE SAFETY CONTROL-BY-EVENT FUNCTION SPECIFIED BELOW CONTROLLED BY A DEDICATED SWITCH, ADD IT BELOW. COORDINATE SUBPARAGRAPH BELOW WITH SYSTEM DESCRIPTION.

6. Switch modules for manual operation of specific life safety control-by-event control points:

a. Alarm notification appliances.
F. Remote Annunciators: Edward’s 2-3-ANND, 3-ANN, Notifer’s INA/ACS, or Simplex’s 4603, having:

SELECT ONE OF NEXT TWO SUBPARAGRAPHS.

1. Surface mounted enclosure.

2. Flush mounted enclosure.

3. LCD which is capable of displaying all system points.

4. System alarm indication (audible and visible).

5. System supervision alarm indication (audible and visible).

6. System trouble indication (audible and visible).

7. Lamp test switch or supervised lamps.


2.02 INITIATING DEVICES
SEE INFORMATION AT END OF SECTION FOR SMOKE AND HEAT SENSING DEVICE APPLICATION GUIDES.

A. General:

1. Fire detection devices that receive their power from the initiating device circuit or a signaling line circuit of a fire alarm control unit shall be listed for use with the control unit.

2. Where individually identifiable (addressable) devices are required, but not available from the Company producing the system, either:

a. Use non-addressable devices and individually wire each device to the FACP’s as separate monitor points, making each non-addressable device individually identifiable, or:

b. Employ remote addressable network modules to make each non-addressable device individually addressable.


B. Ceiling Mounted Detectors (Non-Addressable, Non-Intelligent):

1. General:

a. Heat detectors, ionization type smoke detectors, and photoelectric type smoke detectors shall have common mounting base which accommodates interchanging of the different type detectors.

2. Smoke Detectors:

a. Ionization Type with LED: Edwards’ 6250B, Notifier’s 1451, or Simplex’s 2098-9576.

USE SUBPARAGRAPH BELOW IN LOCATIONS WHERE PHOTOELECTRIC TYPE DETECTOR IS REQUIRED, EXCEPT WHEN THE 135 DEGREES F RATING OF THE THERMAL DEVICE MAY BE INADEQUATE. IN SUCH AREAS USE SECOND SUBPARAGRAPH BELOW (WITHOUT THERMAL DEVICE).

b. Photoelectric Type.

1) With 135 degrees F Thermal Device and LED: Edwards’ 6270B-003, Notifier’s 2451 TH, or Simplex’s 2098-9202.

2) With LED: Edwards’ 6270B, Notifier’s 2451, or Simplex’s 2098-9201.

c. Remote Alarm Indicator For Use with Smoke Detectors: LED type indicator mounted on single gang stainless steel faceplate.

3. Heat Detectors:

a. Fixed Temperature:

1) 135 degrees F: Edwards’ 293B, Notifier’s 5451 HD, or Simplex’s 4098 Series.

2) 190/200 degrees F: Edwards’ 294B, Notifier’s 4451 HT, or Simplex’s 4098 Series.

b. Combination Rate-of-Rise/Fixed Temperature:

1) 135 degrees F: Edwards’ 291B, Notifier’s 5451 TH, or Simplex’s 4098 Series.

2) 190/200 degrees F: Edwards’ 292B, or Simplex’s 4098 Series.


C. Ceiling Mounted Sensors (Intelligent, Addressable, Analog):

1. General:

a. Heat sensors, ionization smoke sensors, and photoelectric smoke sensors shall have common mounting base which accommodates interchanging of the different type sensors.

2. Smoke Sensors:

a. Ionization Type: Edwards’ SIGA-IS, Notifier’s FSI-751, or Simplex’s 4098-9716/9798.

b. Photoelectric Type: Edwards’ SIGA-PS, Notifier’s FSP-751, or Simplex’s 4098-9714/9798.

c. Multi-Sensor Type:

MULTI-SENSOR TYPE SHOULD BE CONSIDERED WERE EARLY DETECTION IS REQUIRED (COMPUTER ROOMS), OR WHERE SINGLE ELEMENT DETECTORS MIGHT BE PRONE TO FALSE ALARMS.

1) Photoelectric/Heat: Edwards’ SIGA-PHS 3D, or Notifier’s FSP-751T

2) Photoelectric/Ionization/Heat: Edwards’ SIGA-IPHS 4D, or Notifier’s IPX-751.

d. Remote Alarm Indicator For Use With Smoke Sensors: Edwards’ SIGA-LED, Notifier’s RA-400, or Simplex’s 4098-9782.

3. Heat Sensors:

a. 135 degrees F (fixed temperature): Edwards’ SIGA-HFS, Notifier’s FST-751, or Simplex’s 4098-9733/9789.

b. 135 degrees F (fixed temperature/R.O.R.): Edwards’ SIGA-HRS, Notifier’s FST-751R, or Simplex’s ________.
D. Air Duct Smoke Detectors (Non-Addressable):

PHOTOELECTRIC DUCT SMOKE DETECTORS ARE PREFERRED. IONIZATION TYPE ARE NOT RECOMMENDED FOR AIR DUCT APPLICATION.

1. Photoelectric Type: Edwards’ 6266B-001, Notifier’s DH400P, or Simplex’s 2098-9649/9201.

a. Listed for the air velocity present at each air duct detector’s location.

b. Sampling tube to suit installation.

c. Local relay (for fire safety control functions from duct detector when applicable):

1) Form C contact(s) rated minimum 1A @ 28Vdc power-limited, 1/2A @ 120Vac nonpower-limited.

2) 24Vdc auxiliary power circuit(s) as required to suit relay operation and function.

SHOW LOCATION OF REMOTE ALARM INDICATORS FOR SMOKE DETECTORS, IF USED.

2. Remote Alarm Indicator For Use With Air Duct Smoke Detectors: LED type indicator mounted on single gang stainless steel faceplate.


E. Air Duct Smoke Sensors (Intelligent, Addressable, Analog):

PHOTOELECTRIC DUCT SMOKE SENSORS ARE PREFERRED. IF IONIZATION TYPE ARE CONSIDERED, CONSULT WITH MANUFACTURER’S REPRESENTATIVE FOR CATALOG NUMBER AND PROPER APPLICATION.

1. Photoelectric Type: Edwards’ SIGA-PS w/SIGA-DH, Notifier’s FSD-751P, or Simplex’s 4098-9752/3 with 4098-9714.

a. Listed for the air velocity present at each air duct smoke sensor’s location.

b. Sampling tube to suit installation.

c. Local relay (for fire safety control functions from duct detector when applicable):

1) Relay operation programmable from FACP.

2) Form C contact(s) rated minimum 1A @ 28Vdc power-limited, 1/2A @ 120Vac nonpower-limited.

3) 24Vdc auxiliary power circuit(s) as required to suit relay operation and function.



SHOW LOCATION OF REMOTE ALARM INDICATORS FOR SMOKE SENSORS, IF USED.

2. Remote Alarm Indicator For Use With Air Duct Smoke Sensors: LED type indicator mounted on single gang stainless steel faceplate.


SPECIFY FLAME DETECTING DEVICES UNDER PARAGRAPH BELOW IF REQUIRED. SEVERAL TYPES OF SPECIALIZED FLAME DETECTING DEVICES ARE AVAILABLE. CONSULT MANUFACTURER’S CATALOGS.
USE FLAME DETECTING DEVICES IN AREAS WHERE IGNITION IS ALMOST INSTANTANEOUS (FLAMMABLE LIQUIDS, COMBUSTIBLE GASES, ETC.) REFER TO NFPA 72 2-4.

F. Flame Detecting Devices (Non-Addressable):


EXPLOSION PROOF DETECTORS ALSO AVAILABLE 190 DEGREES F R.O.R./F.T. AND 135 DEGREES OR 190 DEGREES F FIXED TEMPERATURE. SUITABLE FOR CLASS 1 GROUP D; CLASS II GROUP E, F, G. ALSO AVAILABLE MOISTURE PROOFED.
G. Explosion Proof Rate-of-Rise/Fixed Temperature Heat Detectors (Non-Addressable):

1. 135 degrees F: Edwards’ EPB501, Notifier’s 302-EPM-135, or Simplex’s 2098-9430.



PROJECTED BEAM DETECTORS MAY BE SUITABLE FOR USE IN A BUILDING WITH A HIGH CEILING AND LARGE SPACE WHERE IT IS NOT PRACTICAL TO INSTALL NUMEROUS SPOT TYPE SMOKE DETECTING DEVICES. REFER TO NFPA 72 2-3.6.3.
H. Projected Beam Type Detectors (Non-Addressable): Edwards’ 6424, Notifier’s 6424, or Simplex’s 2098 Series.
I. Manual Fire Alarm Boxes:

1. Non-Addressable:

a. Single Action Pull Type: Edwards’ 276B Series, Notifier’s BNG-1R, or Simplex’s 2099-9754 Series.

b. Security Type (Key Operated): Edwards’ 1534 Series, Notifier’s NBG-10P, Simplex’s 2099-9828 Series. Furnish 2 keys with each station. Furnish 2 tools for installing and servicing the stations (vandal resistant fasteners).

2. Addressable:

a. Single Action Pull Type: Edwards’ SIGA-270, Notifier’s NBG-12LX, or Simplex’s 2099-9795.

b. Security Type (Key Operated): Edwards’ ________, Notifier’s _______, Simplex’s 2099-9795 with cover kit 2099-9828. Furnish 2 keys with each station. Furnish 2 tools for installing and servicing the stations (vandal resistant fasteners).
2.03 NOTIFICATION APPLIANCES
A. General:

1. Provide UL 464 listed audible signal appliances:

a. Classified “Public” or “Private Mode Only” to suit application.

b. Marked “F.A. Service” or “F. A. Service - Private Mode Only” to suit application.

2. Provide UL listed visible signal devices:

a. For private mode applications, UL 1638 “Fire Protective Visual Signaling Appliance”.

b. For public mode applications, UL 1971 “Signaling Devices for the Heating Impaired”.

c. For wall mounting or ceiling mounting to suit application.



15 CANDELA VISIBLE APPLIANCES MAY NOT CURRENTLY (3/01) MEET ADA/ADAAG REQUIREMENTS (WWW.ACCESS-BOARD.GOV) UNTIL A PENDING REVISION IS APPROVED. THE REVISED ADA AND OTHER CODES AND STANDARDS PERTAINING TO VISIBLE REQUIREMENTS WILL BASICALLY BE ALIGNED WITH NFPA 72.
IN LIEU OF SEPARATE APPLIANCES, USE PARAGRAPH BELOW AS THE PREFERRED APPLIANCE WHEN A WALL MOUNTED COMBINATION AUDIBLE/VISIBLE APPLIANCE CAN MEET ALL AUDIBLE AND VISIBLE DESIGN REQUIREMENTS.

B. Combination Audible/Visible Appliances - Wall Mounted:



USE TYPE AV FOR GENERAL WALL MOUNTED USE IN DRY LOCATIONS.

1. Type AV: Edwards’ Genesis Series, Notifier’s SpectrAlert Series, or Simplex’s TrueAlert Series:


SHOW SEPARATE VISIBLE ALARM CIRCUIT AND AUDIBLE ALARM CIRCUIT TO COMBINATION APPLIANCES.

a. Xenon flashtube strobe:

1) AV-15: 15 candela.

2) AV-75: 75 candela.

3) AV-110: 110 candela.

b. Clear lens having FIRE imprinted thereon in red letters, or clear lens with red base having FIRE imprinted thereon in white letters.

c. Audible alarm notification appliance as indicated on the Drawings.

HORN OUTPUT RANGES APPROXIMATELY FROM 80 DBA AT 10 FEET (REVERBERANT CHAMBER-UL 464 TEST) TO 94 DBA AT 10 FEET (ANECHOIC CHAMBER) AND ALSO VARIES DEPENDING ON CODED OR STEADY SIGNAL.

1) Horn.


2) Speaker.

3) Bell.


4) Chime (Electro/Mechanical).

5) Chime (Electronic).

d. Surface or flush wall mounted as indicated on the Drawings.
C. Visible Appliances - Wall Mounted:

TYPE V VISIBLE APPLIANCE IS SUITABLE FOR GENERAL WALL MOUNTED USE IN DRY LOCATIONS.

1. Type V: Edwards’ Genesis Series, Notifier’s SpectrAlert Series, of Simplex’s TrueAlert Series:

a. Xenon flashtube strobe:

1) V-15: 15 candela.

2) V-75: 75 candela.

3) V-110: 110 candela.

b. Clear lens having FIRE imprinted thereon in red letters, or clear lens with red base having FIRE imprinted there on in white letters.

c. Surface or flush wall mounted as indicated on the Drawings.


D. Audible Appliances - Wall Mounted:

1. Horns.



USE TYPE H FOR GENERAL WALL MOUNTED USE IN DRY LOCATIONS.

a. Type H: Edwards’ Genesis Series, Notifier’s SpectrAlert Series, or Simplex’s TrueAlert Series.



HORN OUTPUT RANGES APPROXIMATELY FROM 80 DBA AT 10 FEET (REVERBERANT CHAMBER-UL 464 TEST) TO 94 DBA AT 10 FEET (ANECHOIC CHAMBER) AND ALSO VARIES DEPENDING ON CODED OR STEADY SIGNAL.

1) Surface or flush wall mounted as indicated on the Drawings.



TYPE H-1 TRUMPET TYPE SUITABLE FOR DAMP OR WET LOCATIONS, OR HIGH AMBIENT NOISE APPLICATIONS.

b. Type H-1: Edwards’ 5530D-AW Adaptatone, Notifier’s ________, or Simplex’s 4901-9813:

1) Surface wall mounted.

sound output ranges from 103 to 110 dba at 10 feet, depending on tone.

2) Selectable multiple tone signals.

3) Suitable for damp and wet locations.

2. Vibrating Bells:

a. Type VB: Edwards’ 439D-10AW, Notifier’s KMS or Wheelock MB Series, or Simplex’s 2901 Series Bells:

bells are rated (approximately) 92 dba at 10 feet.

1) 10 inch bells.

2) Surface or flush wall mounted as indicated on the Drawings.

3) Weatherproof bell kits were installed in damp or wet locations.

3. Chimes:

ELECTRO/MECHANICAL CHIME IS RATED (APPROXIMATELY) 75 DBA AT 10 FEET (PRIVATE MODE).

a. Type M (Electro/Mechanical): Edwards’ 329D-AW, Notifier’s ________, or Simplex’s S2902 Series.

1) Surface wall mounted.

ELECTRONIC CHIME IS RATED UP TO 90 DBA AT 10 FEET AT MAXIMUM VOLUME.

b. Type E (Electronic): Edwards’ Integrity 757 Series, Notifier’s Wheelock CH Series, of Simplex’s Wheelock CH Series.

1) Adjustable volume control.

2) Surface or flush wall mounted as indicated on the Drawings.


2.04 ELECTROMAGNETIC DOOR HOLD-OPEN RELEASE DEVICES
COORDINATE WITH HARDWARE GROUP. CONSTRUCTION MAY INCLUDE SPECIFIED DEVICES IN PARAGRAPH BELOW OR OTHER TYPES IN THEIR CONTRACT.

A. Electromagnetic Door Hold-Open Devices: Edwards’ 1500 Series, Notifier’s FM Series, or Simplex’s 2088 Series, having:



DOOR HOLD-OPEN DEVICES SHALL BE MONITORED FOR INTEGRITY (NFPA 72 3-9.6.3). NFPA 72 3-9.2.1 EXCEPTION ALLOWS RELAYS OR APPLIANCES THAT OPERATE ON LOSS OF POWER TO BE CONSIDERED SELF-MONITORING FOR INTEGRITY.
WHEN USING 120VAC, SHOW LOCAL 120VAC CIRCUITS CONTROLLED BY RELAYS CONNECTED TO THE ICU’S.
WHEN USING 24VDC, VERIFY THAT ICU POWER SUPPLY CAN ACCOMMODATE THE REQUIRED NUMBER OF DOOR HOLD OPEN DEVICES. MODIFY SUBPARAGRAPH BELOW TO SUIT.

1. Input circuit suitable for operation on 120Vac.

a. Listed relay for control of 120Vac door hold-open release devices suitable for operation on 24Vdc. Relay operates on loss of power to release door (self-monitoring for integrity).

SHOW WHERE ELECTROMAGNETIC DOOR HOLD-OPEN DEVICES ARE REQUIRED AND TYPE OF MOUNTING (SINGLE DOOR, DOUBLE DOOR, WALL, TYPE OF ARMATURE/CONTACT PLATE). AVOID FLOOR MOUNTING (HARD TO CLEAN AROUND AND PEOPLE TRIP OVER THEM).

2. Style (single door, double door, wall, type of armature/contact plate) suitable for the application.

a. Wall style designed for surface or flush mounting as indicated on the drawings.
2.05 AUTOMATIC FIRE SUPPRESSION SYSTEM SIGNAL ATTACHMENTS
COORDINATE WITH PLUMBING. PLUMBING MAY INCLUDE THE SPECIFIED ATTACHMENTS OR OTHER TYPES IN THEIR CONTRACT.

A. General:

1. Use non-addressable devices and individually wire each device to the FACP’s as separate monitor points, making each non-addressable device individually identifiable, or

2. Employ remote addressable network modules to make each non-addressable device individually addressable.


B. Sprinkler Valve Supervisory Switches:

1. For Outside Screw & Yoke Gate Valves: Grinnell’s Model F640, Notifier’s OSY2, Potter Electric Signal Co.’s OSYS Series, or Simplex’s 2097 Series.

2. For Post Indicator Valves: Potter Electric Signal Co.’s PCVS Series, Notifier’s P1BV2, or Simplex’s 2097 Series.

3. For Gate Valves (Non-Rising Stem) and Special Applications: Potter Electric Signal Co.’s PTS, Notifier’s ________, or Simplex’s 2097 Series.


OTHER TYPE SIGNAL ATTACHMENTS ARE AVAILABLE FOR AIR PRESSURE, WATER LEVEL, AND TEMPERATURE.

C. Tamper Switches: By Micro Switch or Square D Company to suit installation conditions.


D. Waterflow Switch, Vane Type: Autocall Div., Federal Signal Corp.’s 4160, Notifier’s WFD Series, Potter Electric Signal Co.’s VSR-D, Reliable’s Model A or Simplex’s 2097 Series having:

1. Corrosion-resistant vane.

2. Splash/dust resistant enclosure with anti-tamper switch.

3. Adjustable pneumatic retard.

4. Screw type wiring terminals.

5. Switch rated minimum 7.0 amps at 125 Vac and 0.25 amps at 125 Vdc.


2.06 PROTECTIVE DEVICES
SHOW PULL STATIONS EQUIPPED WITH PROTECTIVE SHIELDS IN AREAS SUBJECT TO VANDALISM AND PRANK ALARMS.

A. Pull Station Protective Shield: Clear Lexan shield and red frame covering manual pull station. When shield is lifted a battery powered warning horn is activated. The horn is silenced by lowering and realigning the shield.

1. Edwards’ STI Series Stopper II, Notifier’s STI Stopper II, Safety Technology International Inc.’s STI Stopper II, or Simplex’s 2099 Series (STI) including:

a. Batteries.

b. Weatherproof shield for damp and wet locations.

c. Mounting accessories.



SHOW BELLS EQUIPPED WITH PROTECTIVE GRID WHERE SUBJECT TO SIGNIFICANT IMPACT OR VANDALISM.
B. Protective Grid for Bells: Edwards’ Full Cast Grid, Notifier’s ________, or Simplex’s ________.

STEEL WEB GUARDS ARE INTENDED TO BE SUPPLIED AS SPARE PARTS, TO BE INSTALLED AS NEEDED BY DOCS MAINTENANCE PERSONNEL. DO NOT SHOW SMOKE OR HEAT DETECTION DEVICES ON THE DRAWINGS EQUIPPED WITH STEEL WEB GUARDS UNLESS OTHERWISE ADVISED BY DOCS.
C. Steel Web Guards.

1. For Smoke and Heat Detection Devices: Edwards’ 1206B, Notifier’s STI Steel Web Stoppers, Safety Technology International Inc.’s STI Steel Web Stoppers, or Simplex’s 2098 Series.

2. Steel Web Guards for General Application (Horns, Strobes, Beam Detectors, Speakers, Bells, etc.):

OTHER GAGES AND FINISHES ARE AVAILABLE.

a. Construction:

1) All welded 7 gage wire.

2) Nickel plated finish with lacquer coating.

b. Manufacturer: Chase Security Systems, Inc. 5947 North Milwaukee Avenue, Chicago, IL 60646, Telephone (773) 775-7148, FAX (773) 594-0078.
2.07 TERMINAL STRIP CABINETS
A. Lockable, vandal resistant, surface mounted cabinets constructed of 14 gage steel, size as recommended by the Company producing the system. Equip cabinets with barrier type double screw terminals rated 300 V minimum, meeting UL 94 requirements for materials classed 94 V-0. Use identification strips, tags or labels to identify each conductor. Paint cabinets fire department red and stencil on front in 1/2 inch high white letters, the purpose of each terminal strip cabinet.
2.08 POWER-LIMITED FIRE ALARM CIRCUIT CONDUCTORS
A. All electrical characteristics shall meet the requirements of the Company producing the system (conductor to conductor capacitance, dc resistance, velocity of propagation etc.).
B. Multiconductor Cables NFPA 70 type FPLP, FPLR, FPL:

1. Insulated copper conductors.

2. Conductors twisted, shielded and jacketed as recommended by the Company producing the system.

3. Voltage rating of not less than 300 volts (Voltage rating not marked on cable except where cable has multiple listings and voltage marking is required for one or more of the listings).


C. Other types of cables may be used in accordance with NFPA 70 Table 760-61 “Cable Uses and Permitted Substitutions”, as approved, if listed as being suitable for the purpose.
2.09 NONPOWER-LIMITED FIRE ALARM CIRCUIT CONDUCTORS
A. All electrical characteristics shall meet the requirements of the Company producing the system (conductor to conductor capacitance, dc resistance, velocity of propagation, etc.).
B. Conductors twisted, shielded and jacketed as recommended by the Company producing the system.
C. Single Conductors:

1. No. 18 and No. 16 AWG: Insulated copper conductors suitable for 600 volts, NFPA 70 types KF-2, KFF-2, PAFF, PTFF, PF, PFF, PGF, PGFF, RFH-2, RFHH-2, RFHH-3, SF-2, SFF-2, TF, TFF, TFN, TFFN, ZF, ZFF.

2. Larger Than No. 16 AWG: Insulated copper conductors suitable for 600 volts, in compliance with NFPA 70 Article 310.

3. Conductors with other types and thickness of insulation may be used if listed for nonpower-limited fire alarm circuit use.


D. Multiconductor Cables NFPA 70 Types NPLFP, NPLFR, NPLF:

1. Conductors:

a. Conductor Sizes No. 18 and No. 16 AWG: Insulated copper conductors rated 600 volts, NFPA 70 types KF-2, KFF-2, PAFF, PTFF, PF, PFF, PGF, PGFF, RFH-2, RFHH-2, RFHH-3, SF-2, SFF-2, TF, TFF, TFN, TFFN, ZF, ZFF.

b. No. 14 AWG and Larger: Insulated copper conductors suitable for 600 volts, one of the types listed in NFPA 70 Table 310-13 or one that is identified for nonpower-limited fire alarm circuit use.

c. Cable Listing and Marking: NPLFP, NPLFR, and NPLF marked to suit listings may be and marked with a maximum usage voltage rating of 150 volts.
2.10 MC CABLE
A. Metal-Clad Cable, NFPA 70 Type MC:

1. All electrical characteristics shall meet the requirements of the Company producing the system (conductor to conductor capacitance, dc resistance, velocity of propagation, etc.).

2. Conductors twisted, shielded and jacketed as recommended by the Company producing the system.

3. Interlocked flexible galvanized steel armor sheath conforming to UL requirement for Type MC metal clad cable.

4. Insulated copper conductors suitable for 600 volts:

a. No. 18 and No. 16 AWG: A type listed in NFPA 70 Table 402-3 with a maximum operating temperature not less than 90°C, or types KF-2, KFF-2, PAF, PAFF, PTFF, PF, PFF, PGF, PGFF, PTF, PTFF, SF-2, SFF-2, ZF, ZFF.

b. No. 14 AWG and Larger: One of the types listed in NFPA 70 Table 310-13 or of a type identified for use in Type MC cable.

5. Acceptable Companies: AFC Cable Systems Inc., Coleman Cable Co.

6. Connectors for MC cable: AFC Fitting Inc.’s AFC Series, Arlington Industries Inc.’s Saddle Grip, or Thomas & Betts Co.’s Tite-Bite with anti-short Bushings.
2.11 2-HOUR FIRE RATED CABLE ASSEMBLIES
A. Fire Alarm Circuit Integrity (CI) Cable: Cables identified as meeting the requirements for circuit integrity shall have the additional classification using the suffix “CI”. Examples: FPLP-CI, FPLR-CI, FPL-CI, NPLFP-CI, NPLFR-CI, NPLP-CI.

1. Cables shall have a minimum 2-hour fire resistance rating for the cable when tested in accordance with the Standard for Tests of Fire Resistive Cables-UL 2196.


B. MI Cable: AFC Cable Systems’ MI cable, or BICC/Pyrotenax Mineral Insulated System 1850 Pyrotenax Cable:

MI CABLE IS AVAILABLE IN SEVERAL CONFIGURATIONS AND MATERIALS. CONSULT MANUFACTURER’S CATALOGS. ALSO AVAILABLE NO. 16 AWG.

1. All electrical characteristics shall meet the requirements of the Company producing the system (conductor to conductor capacitance, dc resistance, velocity of propagation, etc.).

2. Solid copper conductors, twisted, shielded as recommended by the Company producing the system.

SYSTEM 1850 COPPER IS RATED TO 1850 DEGREES F AND IS SUITABLE FOR GENERAL USE. STAINLESS STEEL SYSTEMS ARE AVAILABLE, RATED 2000 AND 2200 DEGREES F, AND ARE SUITED TO SOME APPLICATIONS WHERE CORROSION OR CHEMICALS MAY BE DELETERIOUS TO COPPER SHEATH.

3. Seamless copper sheath.

4. Two hour fire resistive rating UL system classified, listed in UL Fire Resistance Directory product category Electrical Circuit Protective Systems (FHIT) and Fire Resistive Cables (FHJR).

5. PVC or HDPE jacketing (where shown on drawings).



INCLUDE SUBPARAGRAPH BELOW WHEN INCREASED CORROSION PROTECTION IS REQUIRED.

6. Accessories as required for a complete system to suit installation conditions.


C. Other 2-hour Fire Resistive Cables: Listed in UL Buildings Materials Directory, product category Electrical Circuit Protective Systems (FHIT), and Fire Resistive Cables (FHIT):

1. Type MC/CI: Rockbestos – Surprenant Cable Corp.’s VITALink MC Circuit Integrity Cable (FHJR System No. 17).

a. PVC jacketing (where shown on drawings).

2. Type FPL/EMT: Rockbestos – Surprenant Cable Corp.’s VITALink FA UL Listed Type FPL installed within ¾” EMT steel conduit (FHIT System No. 22).


2.12 SIGNS, LABELS, MARKERS, AND NAMEPLATES
A. Procedure Sign: Card holder with aluminum or stainless steel frame, plexiglass front and sheet aluminum card backing plate. Minimum size card 8 x 10 inches. For each procedure sign furnish l blank card in holder and 5 spare blank cards suitable for typing future procedures thereon.
OMIT PARAGRAPH BELOW IF RACC IS NOT USED.

B. Alarm Notification Locator: Card holder with aluminum or stainless steel frame, plexiglass front and sheet aluminum card backing plate. Minimum size card 8 x 10 inches. Type on card the switch numbers and location of notification appliances controlled by each switch.


C. Nameplates: Precision engrave letters and numbers with uniform margins, character size minimum 3/16 inch high.

1. Phenolic: Two color laminated engraver’s stock, 1/16 inch minimum thickness, machine engraved to expose inner core color (white).

2. Aluminum: Standard aluminum alloy plate stock, minimum .032 inches thick, engraved areas enamel filled or background enameled with natural aluminum engraved characters.

3. Materials for Outdoor Applications: As recommended by nameplate manufacturer to suit environmental conditions.


D. Fire Alarm Signs: 9 x 12 inches, metal, with the words “FIRE ALARM” imprinted thereon in white letters upon a red background. Include a white arrow pointing down, left or right showing the route to, or actual location of the fire alarm stations. Frame the outside edges of the signs in red and white diagonal stripes.

1. Sign Mounting Styles:

a. Single face for mounting flat against the wall.

b. Double faced for mounting extended from wall.


E. Markers:

a. Premarked self-adhesive; W.H. Brady Co.’s B292, B708, Ideal Industries’ Mylar/Cloth wire markers, or Markwick Corp.’s permanent wire markers, Plastic Extruded Parts Inc.’s Flexible Sleeve or ID Band Markers, or Thomas and Betts Co.’s E-Z Code WSL self-laminating.

b. Other Styles: To suit application by W.H. Brady Co., Ideal Industries, Marwick Corp., Plastic Extruded Parts, Inc., or Thomas and Betts Co.
2.13 SYSTEM KEYING
A. All system locks, key switches, etc., shall operate with the same key.
2.14 ACCESSORIES
A. Include accessories required to perform the functions summarized in SYSTEM DESCRIPTION and indicated on the drawings.

1   2   3


The database is protected by copyright ©dentisty.org 2016
send message

    Main page